13034552599
山東鍍鋅板風管在安裝過程中應該注意的點
瀏覽： |
2019-12-16 12:19
山東鍍鋅板風管在安裝過程中應該注意的點
Points to be paid attention to during the installation of Shandong galvanized sheet air duct
山東鍍鋅板風管具有內外壁光滑，風道阻力小，送排風時不產生二次噪聲，降低能耗，節約運行費用等眾多***勢，為此它得到了廣***用戶的一致認可，那么今天我們要給***家整理介紹一下有關于鍍山東鋅板風管在安裝過程中應該注意的問題，下面我們來具體了解一下，如下：
Shandong galvanized sheet air duct has many advantages, such as smooth internal and external walls, small resistance of air duct, no secondary noise during air supply and exhaust, energy consumption reduction, operation cost saving, etc., so it has been unanimously recognized by the majority of users. Today, we will introduce some problems that should be paid attention to in the installation process of Shandong galvanized sheet air duct. Let's have a specific understanding Next, as follows:
注意一、鍍鋅板風管水平安裝[2] ，直徑或長邊尺寸小于等于400mm，間距不應***于4m；***于 400mm，不應***于3m。鍍鋅板風管的支、吊架間距可分別延長至5m 和3.75m；對于薄鋼板法蘭的鍍鋅板風管，其支、吊架間距不應***于3m。
Note 1. The galvanized sheet air duct shall be installed horizontally [2], the diameter or long side size shall be less than or equal to 400mm, and the spacing shall not be greater than 4m; if it is greater than 400mm, it shall not be greater than 3m. The spacing between the supports and hangers of the galvanized sheet air duct can be extended to 5M and 3.75m respectively; for the galvanized sheet air duct with sheet steel flange, the spacing between the supports and hangers shall not be more than 3m.
山東鍍鋅風管
Shandong galvanized air duct
注意二、鍍鋅板風管垂直安裝，間距不應***于4m，單根直管至少應有2 個固定點。
Note II. The galvanized sheet air duct shall be installed vertically with a spacing of no more than 4m. A single straight pipe shall have at least 2 fixing points.
注意三、鍍鋅板風管支、吊架宜按***標圖集與規范選用強度和剛度相適應的形式和規格。對于直徑或邊長***于2500mm 的超寬、超重等***殊鍍鋅板風管的支、吊架應按設計規定。
Note 3. The support and hanger of galvanized sheet air duct should select the form and specification suitable for the strength and rigidity according to the national standard atlas and specifications. For the support and hanger of special galvanized sheet air duct with diameter or side length greater than 2500mm, the design requirements shall be followed.
注意四、支、吊架不宜設置在風口、閥門、檢查門及自控機構處，離風口或插接管的距離不宜小于200mm。
Note IV. the support and hanger should not be set at the air outlet, valve, inspection door and automatic control mechanism, and the distance from the air outlet or plug-in pipe should not be less than 200mm.
以上是關于山東鍍鋅板風管在安裝過程中應該注意的點，如需了解更多關于鍍鋅風管的知識，敬請關注小編的下期文章更新。
The above is about the points that should be paid attention to during the installation of Shandong galvanized sheet air duct. If you need to know more about galvanized air duct, please pay attention to the next article update of the editor.
